상세검색
최근 검색어 전체 삭제
다국어입력
즐겨찾기0
마이크로전자 및 패키징학회지 제30권 제1호.jpg
KCI등재 학술저널

Ni-foam/Sn-3.0Ag-0.5Cu 복합 솔더 소재를 이용한 EV 파워 모듈 패키지용 천이 액상 확산 접합 연구

A Study of Transient Liquid Phase Bonding with Ni-foam/Sn-3.0Ag-0.5Cu Composite Solder for EV Power Module Package Application

DOI : 10.6117/kmeps.2023.30.1.055
  • 9

본 연구에서는 서로 다른 Pore per inch (PPI, 1 inch 당 pore의 수)를 갖는 Ni-foam 사이에 Sn-3.0Ag-0.5Cu (wt.%, SAC305) 솔더 침지 공정을 수행하여 Ni-foam/SAC305 복합 솔더를 제조한 후, 이를 천이액상 확산 접합(Transient liquid Phase bonding, TLP bonding) 공정에 적용하여 형성된 접합부의 미세구조 분석 및 기계적 특성 평가가수행되었다. 제조된 Ni-foam/SAC305 복합 솔더 프리폼 (Solder preform)은 Ni-foam 및 SAC305로 구성되었으며, Nifoam 계면에는 (Ni,Cu)3Sn4 조성의 금속간 화합물이 형성되었다. TLP 접합 공정 수행 시, Ni-foam 계면의 금속간 화합물은 (Ni,Cu)3Sn4+Au로 변환 되었으며, 접합 시간이 증가할수록 Ni-foam과 SAC305가 지속적으로 반응하면서 접합부는금속간 화합물로 변환되었다. 130 PPI Ni-foam/SAC305 복합 솔더 접합부가 가장 빠른 속도로 금속간 화합물로 변화되는 것을 확인하였다. 기계적 특성에 미치는 Ni-foam의 영향을 확인하기 위해 전단 시험 수행 결과, TLP 접합 초기에 모든 조건의 솔더 접합부는 50 MPa 이상의 우수한 기계적 특성을 나타내었으며, 접합 시간이 증가할수록 전단 강도는 증가하는 경향을 나타내었다.

In this study, Sn-3.0Ag-0.5Cu (wt.%, SAC305) solder dipping process was performed between Ni-foam skeleton with different pore per inch (PPI) to fabricate Ni-foam/SAC305 composite solder, and then applied to the transient liquid phase (TLP) bonding process to evaluate the microstructure and mechanical properties of the bonded joint. The Ni-foam/SAC305 composite solder preform consisted of Ni-foam and SAC305, and an intermetallic compound (IMC) having a (Ni,Cu)3Sn4 composition was formed at the Ni-foam interface. During TLP bonding process, the IMC at the Ni-foam interface was converted to (Ni,Cu)3Sn4+Au, and as the bonding time increased, the Ni-foam and SAC305 continuously reacted, and the bonded joint was converted into an IMC. And it was confirmed that the 130 PPI Ni-foam/ SAC305 composite solder joint was converted into an IMC at the fastest rate. As a result of performing a shear test to confirm the effect of Ni-foam on mechanical properties, solder joints under all conditions exhibited excellent mechanical properties of 50 MPa or more in the early stages of the TLP bonding process, and the shear strength tends to increase as the bonding time increases.

1. 서 론

2. 실험 방법

3. 실험 결과 및 고찰

4. 결 론

감사의 글

References

로딩중